auto moto volkswagen tiguan

auto moto volkswagen tiguan

brought to you by 1aauto.com, your sourcefor quality replacement parts and the best service on the internet. hi, i'm don from 1a auto. i hope this how-to video helps you out, andnext time you need parts for your vehicle, think of 1aauto.com. thanks. in this video we're going to show you howto replace a front window regulator on this 2004 volkswagen jetta and we show you on thedriver side, but the passenger side is similar in procedure.

the items you need is a new window regulatorfrom 1aauto.com, flat blade screwdriver, phillips screwdriver, t20 and t30 torx bits and ratchet,10mm socket, pliers, drill with 5/16 inch drill bit, rivet gun and rivets and some electricaltape. start off by prying off this panel insideyour pull handle. now lift your switch panel up and out andjust push the tab on this harness and disconnect it and then using a phillips screwdriver youwant to remove these three phillips screws. we'll just fast forward as don removes thoseand at the bottom of your door panel you want to remove these three t20 torx bolts and we'llfast forward as don removes those. then just remove this phillips screw up herein the top corner of your door panel.

reach in behind the door panel and just pullout, release the clips then lift it up in out of the window and over the lock .then,you want to pull back on this clip and lift the hook up and out of the door handle. push the tab on this harness and release itand the same for this, push the tabs on either side of this harness and pull it free andthen just push the tabs on the rest of these harnesses and pull them free and now your door panel is free. pull these harnesses from this bracket andyou just push the tabs on either side and pull the harnesses free and do the same thingfor the speaker harness and for this harness

you want to just pry down the bottom. once you pry down hard enough the harnesswill pop free and you just pull it off. then, pull the harness from these tabs onthe door and you could just pull these clips right out of the door but they typically breakso we recommend doing it this way and just pulling the harness from them. now, just pull this gasket out. flip down these two rubber covers and nowremove these three t30 bolts and we'll just fast forward as don does this. now, the motor will just pull free.

now the motor is removed you can lift thewindow up by hand and you want to just lift it up until you can see these clamps on thewindow right here and then you want to remove those two t20 bolts. now separate those clamps from the windowand pull the window up and now you want to remove the series of 10mm bolts lining the window regulator. now, we'll just fast forward as don removesthese. using a flat blade screwdriver push the fourtabs on this clip and push it through the panel. now, you want to lift the panel up and slideit to the outside of the vehicle

and then down. now, push the door handle cable through thepanel and then push this tab on the side here up and over the edge of the door and anglethe door panel down, pull he regulator out and then lift it up and over the lock rodpushing this gasket through. now, just release this harness by pushingon the tab and pulling it free. next, remove these two rubber caps and using a pair of pliers just pinch the sides of these clips and just pull them free. we'll fast forward as don does the rest ofthese. next you want to drill out these four rivetsthat hold in your speaker

and we'll just fast forward as don does thisand it helps to remove that top cover when you do this. ppry the speaker free. on the left is the old window regulator; onthe right is the new one from 1a auto. you can see they're identical and they'regoing to fit exactly the same. reattach the speaker, lie it up and make surethat you have the connector for the harness facing up and we're using rivets to rivetit up together. you can do it this way or some appropriatesize coarse thread or sheet metal bolts will work to attach it as well.

if you removed it replace the top part ofthe speaker and then replace those harness clips. then remove the packing wire tie and thenpush these rubber caps into your new window regulator. pull this harness back through your regulatorpanel, pulling that gasket into place. reclip the harness to the panel and then reconnectthe harness. push the door handle cable back through thepanel and then put it up over the lock rod and overthe gasket, tuck the regulator back up into the door, making sure your harnesses aren'tgoing to get pinched behind it and then push

it back up into place. you do want to make sure that you pull yourdoor handle cable gasket back through the now do the same thing with your lock rod gasketand pull it back up through and into the panel and then put this insulation back down overyour lock rod, if it fell off, and replace those 10mm bolts. we'll just fast forward as don does this. now, you want to loosen up these 10mm boltson your new window clamps and then you want to make sure that those clamps separate andthen slide your window down into place and once it's securely in the clamps just tightenup those bolts.

push those rubber caps back into place andreplace your motor and replace those three t30 bolts. now, reconnect your harnesses and with your motor harness make sure that you push that tab back up to lock it. now if you pull these clips out with the harnessthen you can just push the clips back in. if you pulled the harness from the clips thenyou just want to retape them to those clips with some electrical tape. now to reinstall your door panel, you justwant to reconnect these harnesses and then take your door handle rod and youwant to hook it back into the door handle

and then slide that clip back into the doorhandle. now, put the panel up over the lock rod andthen down into the window sill. make sure you pull your harness for your switchback up through and then line up the clips and hit them back into the door. now, we'll fast forward as don replaces andtightens up those three phillips screws. then, replace those three t20s and replacethat phillips screw up in the top corner and tighten it up. now reconnect your switch panel and then justpush the panel down into place and then line up this panel and push it firmly into placeand you're all set.

we hope this video helps you out. brought to you by www.1aauto.com, your sourcefor quality replacement parts and the best please feel free to call us toll-free, 888-844-3393. we're the company that's here for you on theinternet and in person.

0 Response to "auto moto volkswagen tiguan"

Posting Komentar